Network settings
This section lists network parameters.
Prerequisites
Identification
- Property:
Properties.API.HTTP.Version=3 - Firmware: 5.00 and later.
Parameters
Network
Network interface settings. The parameters in this group (as opposed to the subgroups of this group) are static network settings. If the Network.BootProto=dhcp these parameters may not be in use. Check the read-only parameters in the subgroups to retrieve actual network settings in use by the Axis product.
Network
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
BootProto | dhcp | dhcp none | admin: read, write | Enable/disable dynamic IP address assignment to the Axis product.dhcp= Enable dynamic IP address assignment to the Axis product. none = Disable dynamic IP address assignment to the Axis product. |
IPAddress | 192.168.0.90 | An IP address | admin: read, write | The IP Address of the Axis product on the network. |
SubnetMask | 255.255.255.0 | An IP address | admin: read, write | The subnet mask. |
Broadcast | 192.168.0.255 | An IP address | admin: read, write | Broadcast address. Used to send information to several recipients simultaneously. |
DefaultRouter | 192.168.0.1 | An IP address | admin: read, write | Default router/gateway used for connecting devices attached to different networks and network segments. |
HostName | axis-<serial number> | A host name | admin: read, write | The name of the Axis product on the network, usually the same as the DNSname. |
DNSServer1 | 0.0.0.0 | An IP address | admin: read, write | Primary Domain Name System server. |
DNSServer2 | 0.0.0.0 | An IP address | admin: read, write | Secondary Domain Name System server. |
DomainName | A domain name | admin: read, write | The name of the domain to which the Axis product belongs. |
Network.ARPPingIPAddress
Enable/disable whether it is possible to set the IP address of the Axis product with ARP/Ping.
Network.ARPPingIPAddress
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
Enabled | yes | yes no | admin: read, write | Enable/disable ARP/Ping IP address setting.yes= Enable ARP/Ping IP address setting. no = Disable ARP/Ping IP address setting. |
Network.Bonjour
Enable/disable Bonjour and set the name to be displayed in Bonjour-clients.
Network.Bonjour
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
Enabled | yes | yes no | admin: read write | Enable/disable Bonjour.yes = Enable Bonjour. no = Disable Bonjour. |
FriendlyName | <product name> - <serial number> | A string | admin: read write | The name of the Axis product. |
Network.DNSUpdate
Dynamic Updates in the Domain Name System according to RFC 2136.
Please note that updating the DNS name will require a sequence of VAPIX commands described below. This will initiate a new DNS name update from your Axis device to the DNS server, however issuing just an update of the Network.DNSUpdate.DNSName is not enough to trigger a new DNS update request.
Step 1
http://ip-address/axis-cgi/param.cgi?action=update&Network.DNSUpdate.DNSName=axistest.r2d2.lab
Step 2
http://ip-address/axis-cgi/dnsupdate.cgi?add=axistest.r2d2.lab&hdgen=yes
Network.DNSUpdate
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
DNSName | Fully Qualified Domain Name or host name. | admin: read, write | The name entered here will be associated with the product's IP address in the DNS server. An example of a DNS name is Axisproduct.example.com. | |
Enabled | no | yes no | admin: read, write | Enable/disable dynamic DNS service.yes = Enable dynamic DNS service no = Disable dynamic DNS service |
TTL | 30 | 0 ... <2^32-1> | admin: read, write | This value determines how long (in seconds) the reply from the DNS server should be remembered. |
Network.eth0
Network settings of the first Ethernet interface. Use these parameters to retrieve the network settings actually in use by the Axis product.
Network.eth0
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
Broadcast | An IP address (auto generated). | admin: read | Broadcast address. Used to disseminate information to several recipients simultaneously. | |
IPAddress | An IP address (auto generated). | admin: read operator: read | The IP Address (IPv4) of the Axis product on the network. | |
MACAddress | xx:xx:xx:xx:xx:xx([^1]) | A MAC address (auto generated). | admin: read operator: read | MAC address. The unique identity of the Axis product. |
SubnetMask | An IP address (auto generated). | admin: read | The subnet mask. |
[1]: The MAC address of the Axis product is unique for every single product. The MAC address is the same as the serial number, which can be found on the product's label.
Network.eth0.IPv6
Network settings of IPv6 on the first Ethernet interface. Use these parameters to retrieve the network settings actually in use by the Axis product.
Network.eth0.IPv6
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
| IPAddresses | An IP address (auto generated) | admin: read | The physical addresses of the Axis product on the network. A list of IPv6 addresses, separated by a space. This parameter is read only. |
Network.Filter
IP address filtering. These parameters are used to only accept connections from certain IP addresses or networks.
Network.Filter
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
Enabled | no | yes no | admin: read, write | Enable/disable IP address filtering.yes = Enable IP address filtering. no = Disable IP address filtering. |
Network.Filter.Input
IP addresses filtering for incoming data traffic.
Network.Filter.Input
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
Policy | allow | allow deny | admin: read, write | Allow or deny the addresses access to the Axis product.allow = Allow addresses access to the Axis product. deny = Deny addresses access to the Axis product. |
AcceptAddresses | A string (a space separated list of IP addresses and network addresses in the CIDR notation (IP address/netmask bits)) | admin: read, write | Addresses allowed to pass through the filter. Example: 192.168.0/24 will add all the addresses in the range 192.168.0.0 to 192.168.0.255. If accessing the Axis product via a proxy server, the proxy server's IP address must be added to the list of allowed addresses. |
Network.Filter.Log
Enable/disable logging of filtered packages.
Network.Filter.Log
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
Enabled | no | yes no | admin: read, write | Enable/disable logging of filtered packages.yes = Enable logging of filtered packages. no = Disable logging of filtered packages. |
Network.HTTP.AuthenticationPolicy
Defines the HTTP and RTSP server authentication capabilities in Axis devices from firmware version 5.70 and higher. By using the parameter Network.HTTP.AuthenticationPolicy you can set the authentication capabilities to either basic, digest or basic_digest.
| Mode | HTTP server | RTSP server |
|---|---|---|
Basic | Basic | Basic |
Digest | Digest | Digest |
Basic_Digest | Digest | Basic & Digest |
For RTSP communication, the authentication is performed by default on the RTSP server and controlled via Network.RTSP.AuthenticateRTSPOverHTTP if it has been set to yes. This option can be disabled and System.HTTPAuthRTSPOverHTTP can be used instead to authenticate RTSP requests over HTTP.
Network.Interface.I0.dot1x
The parameters in this group enables the Axis product to access a network protected by IEEE 802.1X/EAPOL (Extensible Authentication Protocol Over Lan).
Network.Interface.I0.dot1x
| Parameter | Default values | Valid values | Access control |
|---|---|---|---|
Enabled | no | yes no | admin: read, write |
EAPOLVersion | 1 | 1 2 3 | admin: read, write |
Status | Stopped | Stopped Unauthorized Authorized UNKNOWN | admin: read, write |
Network.Interface.I0.dot1x.EAPTLS
The parameters in this group sets the identity and password to access to a network protected by IEEE 802.1X/EAPOL (Extensible Authentication Protocol Over Lan).
Network.Interface.I0.dot1x.EAPTLS
| Parameters | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
Identity | A string | admin: read, write | Set the user identity associated with the certificate. A maximum of 128 characters can be used. | |
PrivateKeyPassword | A string | admin: read, write | Set the password for your user identity. A maximum of 16 characters can be used. |
Network.IPv6
Network interface settings for IPv6. The parameters in this group are static network settings. If AcceptRA=yes and/or DHCPv6 is used it will probably result in additional configuration. Check the read-only parameters in the other subgroups to retrieve actual network settings in use by the operation system.
Network.IPv6
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
Enabled | yes | yes no | admin: read, write operator: read viewer: read | Enable/disable IPv6 in the Axis product.yes = Enable IPv6 in the Axis product. no = Disable IPv6 in the Axis product. |
AcceptRA | yes | yes no | admin: read, write | Enable/disable IPv6 to accept router advertisements.yes = Enable IPv6 to accept router advertisements. no = Disable IPv6 to accept router advertisements. |
DHCPv6 | auto | auto stateful stateless off | admin: read, write | Setting for support of DHCPv6.auto = Enable DHCPv6 according to the router advertisements. stateful = Enable DHCPv6 to set IPv6 configuration as well as DNS servers etc. stateless = Enable DHCPv6 only to set DNS servers etc. off = Disable DHCPv6 |
IPAddress | One or more IPv6 addresses | admin: read, write | A list of manually configured IPv6 addresses, separated by a space. (If no prefix length is included in an IPv6 address, the default value 64 is used) | |
DefaultRouter | An IPv6 address | admin: read, write | A manually configured IPv6 address of a default router. |
Network.QoS.Class1
Quality of Service classification. These parameters holds the DSCP value common for the members of a QoS class.
Network.QoS.Class1
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
Desc | Description string | A string | admin: read, write | The description of the QoS class. |
DSCP | 0 | 0 ... 63 | admin: read, write | The Differentiated Services Codepoint value for the QoS class. |
Network.QoS.Class2
Quality of Service classification. These parameters holds the DSCP value common for the members of a QoS class.
Network.QoS.Class2
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
Desc | Description string | A string | admin: read, write | The description of the QoS class. |
DSCP | 0 | 0 ... 63 | admin: read, write | The Differentiated Services Codepoint value for the QoS class. |
Network.QoS.Class3
Quality of Service classification. These parameters holds the DSCP value common for the members of a QoS class.
Network.QoS.Class3
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
Desc | Description string | A string | admin: read, write | The description of the QoS class. |
DSCP | 0 | 0 ... 63 | admin: read, write | The Differentiated Services Codepoint value for the QoS class. |
Network.QoS.Class4
Quality of Service classification. These parameters holds the DSCP value common for the members of a QoS class.
Network.QoS.Class4
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
Desc | Description string | A string | admin: read, write | The description of the QoS class. |
DSCP | 0 | 0 ... 63 | admin: read, write | The Differentiated Services Codepoint value for the QoS class. |
Network.Resolver
Enable/disable retrieval of Domain Name System (DNS) settings from DHCP server. The actual DNS settings in use by the Axis product are located in this group.
Network.Resolver
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
NameServerList | Auto generated (Product dependent) | admin: read | A list of IP addresses (both IPv4 and IPv6), separated by a space. | |
ObtainFromDHCP | Product dependent. | yes no | admin: read, write | Specifies if the DNS server should be obtained from a DHCP server. |
Search | Auto generated | admin: read | Search list of hostname lookup. This parameter is read only. | |
NameServer1 | Auto generated | admin: read | Name server IPaddress. This parameter is read only. | |
NameServer2 | Auto generated | admin: read | Name server IPaddress. This parameter is read only. |
Network.Routing
Routing table actually in use by the Axis product.
Network.Routing
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
DefaultRouter | A routing table (auto generated). | admin: read | The routing table. |
Network.Routing.IPv6
Routing table for IPv6 actually in use by the Axis product.
Network.Routing.IPv6
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
DefaultRouter | Auto generated | admin: read | A list of default routers for IPv6. This parameter is read only. |
Network.RTP
Parameters related to multicast RTP.
Network.RTP
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
NbrOfRTPGroups | Hardware dependent | 1 ... | admin: read operator: read viewer: read | The number of RTP groups. One group for each possible multicast presentation (video source). |
StartPort | 50000 | 1024 ... 65532 | admin: read, write | The RTP port range defines the range of ports from which the video/audio ports are automatically selected. This feature is useful if the product is connected to a NAT router with manually configured port mapping. Each RTP session needs 4 ports, which means 4 ports for each unicast session (audio and video) or 4 ports for the multicast session in total. |
EndPort | 50999 | 1025 ... 65535 | admin: read, write | The RTP port range defines the range of ports from which the video/audio ports are automatically selected. This feature is useful if the product is connected to a NAT router with manually configured port mapping. Each RTP session needs 4 ports, which means 4 ports for each unicast session (audio and video) or 4 ports for the multicast session in total. |
VideoDSCP | 0 | 0 ... 63 | admin: read, write | The Differentiated Services Codepoint for video QoS. |
AudioDSCP | 0 | 0 ... 63 | admin: read, write | The Differentiated Services Codepoint for audio QoS. |
Network.RTP.R#
Parameters related to multicast RTP. One group for each possible multicast presentation (for example video source).
Network.RTP.R#
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
VideoAddress | Auto generated | A multicast IP address. | admin: read, write | The multicast IP address to which the multicast RTP video stream is transmitted. The default value is auto generated based on the serial number of the product. |
VideoPort | 0 | 0, 1024 ... 65535 | admin: read, write | The port number for the RTP video stream.0 = The port number is dynamically assigned. |
AudioAddress | Auto generated. | A multicast IP address. | admin: read, write | The IP address to which the multicast RTP audio stream is transmitted. The default value is generated based on the serial number of the product. The parameter is read only in products without audio support.0.0.0.0 = The audio stream is disabled. |
AudioPort | 0 | 0, 1024 ... 65535 | admin: read, write | The port number for the RTP audio stream. The parameter is read only in products without audio support.0 = The port number is dynamically assigned. |
TTL | 5 | 1 ... | admin: read, write | The Time To Live for each UDP packet. This indicates the number of routers/switches that the packet may traverse before being discarded. |
The # is replaced with a group number starting from zero, e.g. Network.RTP.R0.
Network.RTSP
Parameters needed by the RTSP daemon.
Network.RTSP
| Parameter | Default value | Valid values | Access control | Description |
|---|---|---|---|---|
Enabled | yes | yes no | admin: read, write | Enable/disable RTSP support. If disabled, only multicast RTP is available for MPEG4/h.264 delivery.yes = Enable RTSP support. no = Disable RTSP support. |
Port | 554 | 554, 1024 ... 65535 | admin: read, write operator: read viewer: read | The port number for the RTSP daemon. |
Timeout | 60 | 0 ... | admin: read, write | The keep-alive timeout for the RTSP session specified in seconds.0 = Disable the keep-alive timeout. |
ProtViewer | password | password anonymous | admin: read, write | Viewer access type.password = Password protected access. anonymous = Anonymous access. |
AuthenticateOverHTTP | no | yes no | admin: read, write | Configure whether RTSP requests sent over HTTP need to be authenticated.yes = RTSP requests sent over HTTP need to be authenticated. no = RTSP requests sent over HTTP do not need to be authenticated. |
AllowClientTransportSettings | no | yes no | admin: read, write | Configure whether RTSP transport settings such as a multicast address and a port range should be allowed to be configured by client.yes = RTSP transport settings are allowed to be configured by client. no = RTSP transport settings are not allowed to be configured by client. |
Network.UPnP
Enable/disable Universal Plug and Play and set the name to be displayed in UPnP-clients.
Network.UPnP
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
Enabled | yes | yes no | admin: read, write | Enables Universal Plug and Play.yes = Enable Universal Plug and Play. no = Disable Universal Plug and Play. |
FriendlyName | <product name - <serial number> | A string | admin: read, write | The UPnP display name. |
Network.UPnP.NATTraversal
These parameters control NAT traversal functionality. To make the task of port forwarding easier, Axis offers the NAT traversal functionality in many of its network video products. NAT traversal is a technique that can be used to open up routers and firewalls to make devices on a LAN accessible from the Internet.
Network.UPnP.NATTraversal
| Parameter | Default value | Valid values | Access control | Description |
|---|---|---|---|---|
Enabled | no | yes no | admin: read, write | Enables/disables NAT traversal.yes = Enable NAT traversal. no = Disable NAT traversal. |
Router | An IP address | admin: read, write | If an IP address is entered NAT traversal will be attempted with that router. If none is entered, the server will automatically try to discover a router. | |
ExternalIPAddress | An IP address | admin: read | The external IP address of the NAT router. This value shall not be configured. It is set by the system itself. | |
Active | no | yes no | admin: read, write | This parameter is set to yes if NAT traversal was successful. This value shall not be configured, it is set by the system itself.yes = NAT traversal was successful no = NAT traversal was not successful |
MinPort | 32768 | 1 ... 65535 | admin: read, write | The first time NAT traversal is enabled, a random port between MinPort and MaxPort will be selected for the TCP port to map in the router. If port mapping is successful, that port will be used thereafter. The random range can be limited by setting MinPort and MaxPort. |
MaxPort | 65535 | 1 ... 65535 | admin: read, write | The first time NAT traversal is enabled, a random port between MinPort and MaxPort will be selected for the TCP port to map in the router. If port mapping is successful, that port will be used thereafter. The random range can be limited by setting MinPort and MaxPort. |
Network.VolatileHostName
Enable/disable retrieval of host name from DHCP-server. The host name, actually in use by the Axis product, is located in this group.
Network.VolatileHostName
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
ObtainFromDHCP | yes | yes no | admin: read, write | Specifies if the host name should be obtained from a DHCP server.yes = The host name is obtained from a DHCP server. no = The host name is not obtained from a DHCP server. |
HostName | Auto generated | admin: read | The host name obtained from a DHCP server. |
Network.ZeroConf
Enable/disable automatic configuration of link local IP address. The negotiated network settings are located in this group, and are used in parallel with the setting of the Network.eth0 group. That means that both addresses can be used simultaneously.
Network.ZeroConf
| Parameter | Default value | Valid values | Access control | Description |
|---|---|---|---|---|
Enabled | yes | yes no | admin: read, write | Enable/disable zero configuration. yes = Enable zero configuration. no = Disable zero configuration. |
Fallback | no | yes no | admin: read, write | Link-local addressing is only activated if DHCP or static addressing fails. If Enabled = no: Link-local addresses are never used and Fallback is ignored. If Enabled = yes and Fallback = yes: Link-local addresses are only used if the primary address configuration mode (either DHCP or static) fails. If Enabled = yes and Fallback = no: Link-local addresses are always used. |
IPAddress | Auto generated | admin: read | The IP address. | |
SubnetMask | Auto generated | admin: read | The subnet mask. |
SNMP
SNMP (Simple Network Management Protocol) configuration.
SNMP
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
Enabled | no | yes no | admin: read, write | Enable/disable SNMP.yes = Enable SNMP no = Disable SNMP |
InitialUserPasswd | A string. | admin: write | SNMP V3 initial user password. | |
InitialUserPasswdSet | no | yes no | admin: read, write | Set to yes if InitialUserPasswd is set.yes = Enable initial user password. no = Disable initial user password. |
EngineBoots | 0 ... | admin: read, write | Number of times SNMP has started. | |
V1 | no | yes no | admin: read, write | Enable/disable SNMP V1.yes = Enable SNMP V1. no = Disable SNMP V1. |
V2c | no | yes no | admin: read, write | Enable/disable SNMP V2c.yes = Enable SNMP V2c. no = Disable SNMP V2c. |
V3 | no | yes no | admin: read, write | Enable/disable SNMP V3.yes = Enable SNMP V3. no = Disable SNMP V3. |
V1ReadCommunity | public | A string | admin: read, write | The community name used for SNMP V1/V2c read operations. |
V1WriteCommunity | write | A string | admin: read, write | The community name used for SNMP V1/V2c write operations. |
DSCP | 0 | 0 ... 63 | admin: read, write | The Differentiated Services Codepoint for SNMP QoS. |
TransportProtocol | udp | udp tcp | admin: read, write | The transport protocol to be used for SNMP traffic. |
SNMP.Trap
Traps are used by the camera to send messages to a management system for important events or status changes. These settings are used with SNMP v1/v2.
SNMP.Trap
| Parameter | Default value | Valid values | Access control | Description |
|---|---|---|---|---|
| Enabled | no | yes no | admin: read, write | Enable disable trap reporting.yes = Enable trap reporting. No = Disable trap reporting. |
SNMP.Trap.T#
This parameter group contains a parameter for trap messages.
SNMP.Trap.T#
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
Address | An IP address. | admin: read, write | Set the IP address of the management server. | |
Community | A string. | admin: read, write | Set community to use when sending a trap message to the management system. An SNMP community is the group of devices and management station running SNMP. Community names are used to identify groups. |
SNMP.Trap.T#.AuthFail
This parameter group contains a parameter for trap message when authentication attempt fails.
SNMP.Trap.T#.AuthFail
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
Enabled | no | yes no | admin: read, write | Enable/disable trap message when an authentication attempt fails.yes = Enable trap message when an authentication attempt fails. No = Disable trap message when an authentication attempt fails |
SNMP.Trap.T#.Coldstart
This parameter group contains a parameter for trap message when the camera is rebooted/resarted.
SNMP.Trap.T#.Coldstart
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
Enabled | no | yes no | admin: read, write | Enable/disable trap message when the camera is rebooted/restarted.yes = Enable trap message when the camera is rebooted/restarted. no = Disable trap message when the camera is rebooted/restarted. |
SNMP.Trap.T#.LinkUp
This parameter group contains a parameter for a trap message when a link changes from down to up.
SNMP.Trap.T#.LinkUp
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
Enabled | no | yes no | admin: read, write | Enable/disable a trap message when a link changes from down to up.yes = Enable a trap message when a link changes from down to up. no = Disable a trap message when a link changes from down to up. |
SNMP.Trap.T#.WarmStart
This parameter group contains a parameter for a trap message when SNMP has started and the configure file has changed, but not the MIB (Management Information Base).
SNMP.Trap.T#.WarmStart
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
Enabled | no | yes no | admin: read, write | Enable /disable a trap message when SNMP has started and the configure file has changed, but not the MIB (Management Information Base).yes = Enable a trap message when SNMP has started and the configure file has changed, but not the MIB. no = Disable a trap message when SNMP has started and the configure file has changed, but not the MIB. |
SNMP.NTCIP
This parameter group contains a parameter that can be used to enable and disable NTCIP. Please note that SNMP must be enabled before you can use this parameter.
SNMP.NTCIP
| Parameter | Default values | Valid values | Access control | Description |
|---|---|---|---|---|
Enabled | no | yes no | admin: read, write | yes = Enables NTCIP. no = Disables NTCIP. |